 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| a FEATURES 7 ns Propagation Delay Single Supply Operation: +3 V to +10 V Low Power Symmetrical Layout Latch Function TSSOP Packages APPLICATIONS Clock Recovery and Clock Distribution High Speed Data Line Receivers Phase Detectors Digital Communications I and Q Detection High Speed Sampling Upgrade for MAX912 Satellite Receivers PCMCIA Cards Wireless Data Links Battery Operated Instrumentation GENERAL DESCRIPTION Dual 7 ns Single Supply Comparator AD8598 PIN CONFIGURATIONS N-16, RU-16 and R-16A QA 1 QA 2 GND 3 LEA 4 NC 5 V- 6 IN A- 7 IN A+ 8 16 15 14 QB QB GND LEB NC V+ IN B- IN B+ AD8598 TOP VIEW (Not to Scale) 13 12 11 10 9 NC = NO CONNECT The AD8598 is a dual 7 ns comparator with digital latches. Separate supplies enable the input stage to be operated from +5 V to as high as 5 V. Ultrafast 7 ns propagation delay makes the AD8598 a good choice for timing circuits and line receivers. Propagation delays for rising and falling signals are closely matched and track over temperature. This matched delay makes the AD8598 a good choice for clock recovery, since the duty cycle of the output will match the duty cycle of the input. The AD8598 has the same pinout as the DIP version of the AD9698. For a single comparator like the AD8598, please refer to the AD8561 data sheet. The AD8598 is specified over the industrial (-40C to +85C) temperature range. The AD8598 is available in both the 16-lead plastic DIP, 16-lead TSSOP or narrow R-16A surface mount packages. REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 1998 AD8598-SPECIFICATIONS ELECTRICAL SPECIFICATIONS (@ V+ = +5.0 V, V- = V Parameter INPUT CHARACTERISTICS Offset Voltage Offset Voltage Drift Input Bias Current Input Offset Current Input Common-Mode Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain Input Capacitance LATCH ENABLE INPUT Logic "1" Voltage Threshold Logic "0" Voltage Threshold Logic "1" Current Logic "0" Current Latch Enable Pulsewidth Setup Time Hold Time DIGITAL OUTPUTS Logic "1" Voltage Logic "1" Voltage Logic "0" Voltage DYNAMIC PERFORMANCE Propagation Delay Propagation Delay Differential Propagation Delay (Rising Propagation Delay vs. Falling Propagation Delay) Rise Time Fall Time POWER SUPPLY Power Supply Rejection Ratio Positive Supply Current (V+ Pin) Ground Supply Current (GND Pins) Analog Supply Current (V- Pin) NOTES 1 Guaranteed by design. Specifications subject to change without notice. GND = 0 V, TA = +25 C unless otherwise noted) Min Typ 2.3 4 -3 -3.5 Max 7 8 Units mV mV V/C A A A V dB V/V pF V V A A ns ns ns V V V ns ns ns Symbol VOS VOS/T IB IB IOS VCM CMRR AVO CIN VIH VIL IIH IIL tPW(E) tS tH VOH VOH VOL tP tP tP Conditions -40C TA +85C VCM = 0 V -40C TA +85C VCM = 0 V 0 V VCM +3.0 V RL = 10 k -6 -7 0.0 65 4 +3.0 85 +3,000 3.0 +1.65 +1.60 -0.3 -2 6 1 1.2 +2.0 VLH = +3.0 V VLL = +0.3 V -1.0 -4 +0.8 IOH = -50 A, VIN > 250 mV IOH = -3.2 mA, VIN > 250 mV IOL = 3.2 mA, VIN > 250 mV 200 mV Step with 100 mV Overdrive -40C TA +85C 100 mV Step with 5 mV Overdrive 100 mV Step with 100 mV Overdrive1 20% to 80% 80% to 20% +4.5 V V+ +5.5 V -40C TA +85C VO = 0 V, RL = -40C TA +85C -40C TA +85C +3.5 +2.4 +3.5 +0.25 6.75 8 8 +0.4 9.8 13 0.5 3.8 1.5 50 65 9.0 4.4 4.6 2.0 ns ns ns dB mA mA mA mA mA mA PSRR I+ IGND I- 12.0 15.0 6.6 7.6 9.0 11.0 -2- REV. A AD8598 ELECTRICAL SPECIFICATIONS (@ V+ = +5.0 V, V Parameter INPUT CHARACTERISTICS Offset Voltage Offset Voltage Drift Input Bias Current Input Offset Current Input Common-Mode Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain Input Capacitance LATCH ENABLE INPUT Logic "1" Voltage Threshold Logic "0" Voltage Threshold Logic "1" Current Logic "0" Current Latch Enable Pulsewidth Setup Time Hold Time DIGITAL OUTPUTS Logic "1" Voltage Logic "0" Voltage DYNAMIC PERFORMANCE Propagation Delay Propagation Delay Differential Propagation Delay (Rising Propagation Delay vs. Falling Propagation Delay) Rise Time Fall Time Dispersion POWER SUPPLY Power Supply Rejection Ratio Supply Current Positive Supply Current (V+ Pin) Ground Supply Current (GND Pins) Analog Supply Current (V- Pin) NOTES 1 Guaranteed by design. Specifications subject to change without notice. GND = 0 V, V- = -5 V, TA = +25 C unless otherwise noted) Min Typ 1 4 -3 -2.5 Max 7 8 Units mV mV V/C A A A V dB V/V pF V V A A ns ns ns V V ns ns ns Symbol VOS VOS/T IB IB IOS VCM CMRR AVO CIN VIH VIL IIH IIL tPW(E) tS tH VOH VOL tP tP tP Conditions -40C TA +85C VCM = 0 V -40C TA +85C VCM = 0 V -5.0 V VCM +3.0 V RL = 10 k -6 -7 -5.0 65 4 +3.0 85 +3,000 3.0 +1.65 +1.60 -0.5 -2 6 1.0 1.2 +2.0 VLH = +3.0 V VLL = +0.3 V -1 -4 +0.8 IOH = -3.2 mA IOL = 3.2 mA 200 mV Step with 100 mV Overdrive -40C TA +85C 100 mV Step with 5 mV Overdrive 100 mV Step with 100 mV Overdrive1 20% to 80% 80% to 20% +2.6 +3.5 +0.2 6.5 8 7 +0.3 9.8 13 0.5 3.8 1.5 1 55 70 9.4 4.4 4.8 2 ns ns ns ns dB PSRR I+ IGND I- 4.5 V VCC and VEE 5.5 V VO = 0 V, RL = -40C TA +85C VO = 0 V, RL = -40C TA +85C -40C TA +85C 13.0 15.0 6.6 7.6 9.0 11.0 mA mA mA mA mA mA REV. A -3- AD8598-SPECIFICATIONS ELECTRICAL SPECIFICATIONS Parameter INPUT CHARACTERISTICS Offset Voltage Input Bias Current Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output High Voltage1 Output Low Voltage POWER SUPPLY Power Supply Rejection Ratio Supply Currents Positive Supply Current (V+ Pin) Ground Supply Current (GND Pins) Analog Supply Current (V- Pin) DYNAMIC PERFORMANCE Propagation Delay (@ V+ = +3.0 V, V- = VGND = 0 V, TA = +25 C unless otherwise noted) Conditions Min Typ Max 7 VCM = 0 V -40C TA +85C +0.1 V VCM +1.5 V IOH = -3.2 mA, VIN > 250 mV IOL = +3.2 mA, VIN > 250 mV +2.7 V VCC, VEE +6 V VO = 0 V, RL = -40C TA +85C -40C TA +85C -40C TA +85C 100 mV Step with 20 mV Overdrive2 -6 -7 0 50 +1.2 +0.3 40 8.0 3.2 4.8 9.0 11.0 5.0 6.0 6.6 7.6 9.8 -3.0 -4 +1.5 Units mV A A V dB V V dB mA mA mA mA mA mA ns Symbol VOS IB IB VCM CMRR VOH VOL PSRR I+ IGND I- tP 8.5 NOTES 1 Output high voltage without pull-up resistor. It may be useful to have a pull-up resistor to V+ for +3 V operation. 2 Guaranteed by design. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS Total Analog Supply Voltage . . . . . . . . . . . . . . . . . . . . . +14 V Digital Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . +7 V Analog Positive Supply-Digital Positive Supply . . . . . -600 mV Input Voltage1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . 8 V Output Short-Circuit Duration to GND . . . . . . . . . Indefinite Storage Temperature Range N, R, RU Package . . . . . . . . . . . . . . . . . . -65C to +150C Operating Temperature Range . . . . . . . . . . . -40C to +85C Junction Temperature Range N, R, RU Package . . . . . . . . . . . . . . . . . . -65C to +150C Lead Temperature Range (Soldering, 10 sec) . . . . . . . +300C Package Type 16-Lead Plastic DIP 16-Lead SOIC 16-Lead TSSOP 2 JA JC Units C/W C/W C/W 103 158 240 43 43 43 NOTES 1 The analog input voltage is equal to 7 V or the analog supply voltage, whichever is less. 2 JA is specified for the worst case conditions, i.e., JA is specified for device in socket for P-DIP and JA is specified for device soldered in circuit board for SOIC and TSSOP packages. ORDERING GUIDE Model AD8598AN AD8598ARU AD8598AR Temperature Range -40C to +85C -40C to +85C -40C to +85C Package Descriptions 16-Lead Plastic DIP 16-Lead Thin Shrink Small Outline (TSSOP) 16-Lead Narrow Body IC Package Options N-16 RU-16 R-16A CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8598 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE -4- REV. A AD8598 Typical Performance Characteristics (V+ = +5 V, V- = 0 V, T = +25 C unless otherwise noted) A 5 +125 C OUTPUT VOLTAGE - Volts 4 40 C 3 +25 C 2 VS = +5V, SINGLE SUPPLY NUMBER OF COMPARATORS PROPAGATION DELAY - ns 400 15 TA = +25 C 10 500 20 VS = +5V, SINGLE SUPPLY STEP SIZE = 100mV CAPACITANCE LOAD = 10pF 300 200 1 5 100 0 2.5 2.0 1.5 1.0 0.5 0 0.5 1.0 1.5 DIFFERENTIAL INPUT VOLTAGE - mV 0 5 4 3 210 1 2 3 INPUT VOLTAGE - mV 4 5 0 0 10 20 30 OVERDRIVE - mV 40 50 Figure 1. Output Voltage vs. Differential Input Voltage Figure 2. Typical Distribution of Input Offset Voltage Figure 3. Propagation Delay vs. Overdrive 20 VS = +5V, SINGLE SUPPLY STEP SIZE = 100mV OVERDRIVE LOAD = 5mV 15 40 VS = +5V, SINGLE SUPPLY TA = +25 C OVERDRIVE = 10mV CAPACITANCE LOAD = 10pF 30 STEP SIZE = 800mV 200mV 20 400mV 20 SINGLE SUPPLY TA = +25 C STEP SIZE = 100mV OVERDRIVE = 5mV CAPACITANCE LOAD = 10pF PROPAGATION DELAY - ns PROPAGATION DELAY - ns 2 PROPAGATION DELAY - ns 15 tPD 10 FALLING EDGE 10 tPD + FALLING EDGE 5 10 100mV 5 0 0 20 30 40 10 LOAD CAPACITANCE - pF 50 0 0 0.5 1 1.5 SOURCE RESISTANCE - k 0 4.5 4.75 5 5.25 SUPPLY VOLTAGE - Volts 5.5 Figure 4. Propagation Delay vs. Load Capacitance Figure 5. Propagation Delay vs. Source Resistance Figure 6. Propagation Delay vs. Positive Supply Voltage 20 VS = +5V, SINGLE SUPPLY STEP SIZE = 100mV OVERDRIVE = 5mV, LOAD CAPACITANCE = 10pF 20 +25 C PROPAGATION DELAY - ns 15 40 C 10 TIME - ns +125 C 4 PROPAGATION DELAY - ns 15 3 10 2 HOLD TIME SETUP TIME 5 5 VS = +5V STEP SIZE = 100mV OVERDRIVE = 5mV LOAD CAPACITANCE = 10pF 0 2 3 4 1 COMMON-MODE VOLTAGE - Volts 5 1 0 -50 0 -25 0 25 75 50 TEMPERATURE - C 100 125 0 -50 -25 0 25 50 75 TEMPERATURE - C 100 125 Figure 7. Propagation Delay vs. Temperature Figure 8. Propagation Delay vs. VCM Figure 9. Latch Setup-and-Hold Time vs. Temperature REV. A -5- AD8598 0.5 OUTPUT LOW VOLTAGE - Volts 5.0 I-, ANALOG SUPPLY CURRENT - mA 0 OUTPUT HIGH VOLTAGE - Volts 0.4 4.4 TA = +125 C 3.8 TA = +25 C 3.2 TA = 2.6 40 C 4.0 V+ = +5V, V 8.0 V+ = +5V, V 12.0 = 5V = 0V 0.3 TA = 0.2 TA = +125 C 0.1 40 C TA = +25 C 16.0 0 0 3 6 9 12 SINK CURRENT - mA 15 2.0 0 3 6 9 12 SOURCE CURRENT - mA 15 20.0 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE - C Figure 10. Output Low Voltage, VOL vs. Sink Current Figure 11. Output High Voltage, V OH vs. Source Current Figure 12. Analog Supply Current vs. Temperature for 5 V Supplies 0 I-, ANALOG SUPPLY CURRENT - mA 80 0 POSITIVE SUPPLY CURRENT - mA 70 60 50 40 +125 C 30 20 10 0 5 1 10 FREQUENCY - MHz 100 7.5 5 2.5 5 0 2.5 INPUT COMMON-MODE VOLTAGE - Volts +25 C INPUT BIAS CURRENT - A 1 4.0 TA = 8.0 TA = +25 C 12.0 TA = +125 C 16.0 40 C 2 3 -40 C 4 20.0 2 4 6 8 10 SUPPLY VOLTAGE - Volts 12 Figure 13. Analog Supply Current vs. Supply Voltage Figure 14. Positive Supply Current vs. Input Frequency Figure 15. Input Bias Current vs. Input Common-Mode Voltage for 5 V Supplies 0 INPUT BIAS CURRENT - A 1.0 2.0 3.0 4.0 5.0 75 50 25 0 25 50 75 100 125 150 TEMPERATURE - C Figure 16. Input Bias Current vs. Temperature -6- REV. A AD8598 APPLICATIONS Optimizing High Speed Performance Note that signals much greater than +3.0 V will result in increased input currents and may cause the device to operate more slowly. The input bias current of the AD8598 is the same magnitude (-3 A typical) as the MAX912 (+3 A typical), and the current flows out of the AD8598 and into MAX912. If relatively low value resistors and/or low impedance sources are used on the inputs, the voltage shift due to bias current should be small. The AD8598 (6.75 ns typical) is faster than the MAX912 (10 ns typical). While this is beneficial to many systems, timing may need to be adjusted to take advantage of the higher speed. The AD8598 has slightly more output voltage swing when the output is lightly loaded. The AD8598 uses less current (typically 10 mA) than the MAX912 (typically 12 mA). Increasing Output Swing As with any high speed comparator or amplifier, proper design and layout techniques should be used to ensure optimal performance from the AD8598. The performance limits of high speed circuitry can easily be a result of stray capacitance, improper ground impedance or other layout issues. Minimizing resistance from source to the input is an important consideration in maximizing the high speed operation of the AD8598. Source resistance in combination with equivalent input capacitance could cause a lagged response at the input, thus delaying the output. The input capacitance of the AD8598, in combination with stray capacitance from an input pin to ground could result in several picofarads of equivalent capacitance. A combination of 3 k source resistance and 5 pF of input capacitance yields a time constant of 15 ns, which is slower than the 5 ns capability of the AD8598. Source impedances should be less than 1 k for the best performance. It is also important to provide bypass capacitors for the power supply in a high speed application. A 1 F electrolytic bypass capacitor should be placed within 0.5 inches of each power supply pin to ground. These capacitors will reduce any potential voltage ripples from the power supply. In addition, a 10 nF ceramic capacitor should be placed as close as possible from the power supply pins to ground. These capacitors act as a charge reservoir for the device during high frequency switching. A ground plane is recommended for proper high speed performance. This can be created by using a continuous conductive plane over the surface of the circuit board, only allowing breaks in the plane for necessary current paths. The ground plane provides a low inductance ground, eliminating any potential differences at different ground points throughout the circuit board caused from "ground bounce." A proper ground plane also minimizes the effects of stray capacitance on the circuit board. Replacing the MAX912 Although not required for normal operation, the output voltage swing of the AD8598 can be increased by connecting a 5 k resistor from the output of the device to the V+ power supply. This configuration can be useful in low voltage power supply applications where maximizing output voltage swing is important. Adding a 5 k pull-up resistor to the device's output will not adversely affect the specifications of the AD8598. Output Loading Considerations The AD8598 output can deliver up to 40 mA of output current without any significant increase in propagation delay. The output of the device should not be connected to more than twenty (20) TTL input logic gates, nor drive a load resistance less than 100 . To ensure the best performance from the AD8598 it is important to minimize capacitive loading of the output of the device. Capacitive loads greater than 50 pF will cause ringing on the output waveform and will reduce the operating bandwidth of the comparator. Setup and Hold Times for Latching the Output The AD8598 is pin compatible with the MAX912 comparator. While it is easy to replace the MAX912 with the higher performance AD8598, please note that there are differences, and it is useful to check these to ensure proper operation. There are five major differences between the AD8598 and the MAX912; input voltage range, input bias currents, speed, output swing and power consumption. When operated on a +5 V single supply, the MAX912 has an input voltage range from -0.2 V to +3.5 V. The AD8598 has an input range from 0 V to +3.0 V. Signals above +3.0 V may result in slower response times (see Figure 8). If both signals exceed +3.0 V, the signals may be shifted or attenuated to bring them into range, keeping in mind the note about source resistance in Optimizing High Speed Performance. If only one of the signals exceeds +3.0 V only slightly, and the other signal is always well within the 0 V to +3 V range, the comparator may operate without changes to the circuit. Example: A comparator compares a fast moving signal to a fixed +2.5 V reference. Since the comparator only needs to operate when the signal is near +2.5 V, both signals will be within the input range (near +2.5 V and well under +3.0 V) when the comparator needs to change output. The latch inputs can be used to retain data at the outputs of the AD8598. When the voltage at the latch input goes high, the output of the device will remain constant regardless of the input voltages. The setup time for the latch is 2 ns-3 ns and the hold time is 3 ns. This means that to ensure data retention at the output, the input signal must be valid at least 5 ns before the latch pin goes high and must remain valid at least 3 ns after the latch pin goes high. Once the latch input voltage goes low, new output data will appear in approximately 8 ns. A logic high for the latch input is a minimum of +2.0 V and a logic low is a maximum of +0.8 V. This makes the latch input easily interface with TTL or CMOS logic gates. The latch circuitry in the AD8598 has no built-in hysteresis. Input Stage and Bias Currents The AD8598 uses a PNP differential input stage that enables the input common-mode range to extend all the way from the negative supply rail to within +2.2 V of the positive supply rail. The input common-mode voltage can be found as the average of the voltage at the two inputs of the device. To ensure the fastest response time, care should be taken not to allow the input common-mode voltage to exceed either of these voltages. REV. A -7- AD8598 The input bias current for the AD8598 is 3 A. As with any PNP differential input stage, this bias current will go to zero on an input that is high and will double on an input that is low. Care should be taken in choosing resistor values to be connected to the inputs as large resistors could cause significant voltage drops due to the input bias current. The input capacitance for the AD8598 is typically 3 pF. This is measured by inserting a 5 k source resistance to the input and measuring the change in propagation delay. Using Hysteresis The input signal is directly connected to the noninverting input of the comparator. The output is fed back to the inverting input through R1 and R2. The ratio of R1 to R1 + R2 establishes the width of the hysteresis window with VREF setting the center of the window, or the average switching voltage. The Q output will switch high when the input voltage is greater than VHI and will not switch low again until the input voltage is less than VLO as given in Equation 1: V HI = V + -1-V REF Hysteresis can easily be added to a comparator through the addition of positive feedback. Adding hysteresis to a comparator offers an advantage in noisy environments where it is not desirable for the output to toggle between states when the input signal is near the switching threshold. Figure 17 shows a method for configuring the AD8598 with hysteresis. SIGNAL COMPARATOR ( R1 ) R1+ R2 +V REF R1 V LO =V REF 1- R1+ R2 where V+ is the positive supply voltage. (1) VREF R1 R2 The capacitor, CF, can also be added to introduce a pole into the feedback network. This has the effect of increasing the amount of hysteresis at high frequencies. This can be useful when comparing a relatively slow signal in a high frequency noise environment. At 1 , the hysteresis window 2 CF R2 approaches VHI = V+ - 1 V and VLO = 0 V. At frequencies less than fP the threshold voltages remain as in Equation 1. frequencies greater than fP = CF Figure 17. Configuring the AD8598 with Hysteresis -8- REV. A AD8598 SPICE Model * AD8598 SPICE Macro-Model Typical Values * 4/98, Ver. 1.0 * TAM / ADSC * * Node assignments * non-inverting input * | inverting input * | | positive supply * | | | negative * | | | | * | | | | * | | | | * | | | | * | | | | .SUBCKT AD8598 1 2 99 50 * * INPUT STAGE * * Q1 4 3 5 PIX Q2 6 2 5 PIX IBIAS 99 5 800E-6 RC1 4 50 1E3 RC2 6 50 1E3 CL1 4 6 1E-12 CIN 1 2 3E-12 VCM1 99 7 1 D1 5 7 DX EOS 3 1 POLY(1) (31,98) 1E-3 1 * * Reference Voltage * EREF 98 0 POLY(2) (99,0) (50,0) 0 0.5 0.5 RREF 98 0 100E3 * * CMRR=80dB, ZERO AT 1kHz * ECM1 30 98 POLY(2) (1,98) (2,98) 0 0.5 0.5 RCM1 30 31 10E3 RCM2 31 98 1 CCM1 30 31 15.9E-9 * * Latch Section * RX 80 51 100E3 E1 10 98 (4,6) 1 S1 10 11 (80,51) SLATCH1 R2 11 12 1 C3 12 98 10E-12 E2 13 98 (12,98) 1 R3 12 13 500 * * Power Supply Section * supply Latch | | | | 80 DGND | | | 51 Q | | 45 QNOT | 65 REV. A -9- AD8598 GSY1 99 52 POLY(1) (99,50) 4E-3 -2.6E-4 GSY2 52 50 POLY(1) (99,50) 3.7E-3 -.6E-3 RSY 52 51 10 * * Gain Stage Av=250 fp=100MHz * G2 98 20 (12,98) 0.25 R1 20 98 1000 C1 20 98 10E-13 D2 20 21 DX D3 22 20 DX V1 99 21 DC 0.8 V2 22 50 DC 0.8 * * Q Output * Q3 99 41 46 NOX Q4 47 42 50 NOX RB1 43 41 200 RB2 40 42 5E3 CB1 99 41 10E-12 CB2 42 50 5E-12 RO1 46 45 2E3 RO2 47 45 500 EO1 98 43 POLY(1) (20,98) 0 1 EO2 40 98 POLY(1) (20,98) 0 1 * * Q NOT Output * Q5 99 61 66 NOX Q6 67 62 50 NOX RB3 63 61 200 RB4 60 62 5E3 CB3 99 61 10E-12 CB4 62 50 5E-12 RO3 66 65 2E3 RO4 67 65 500 EO3 63 98 POLY(1) (20,98) 0 1 EO4 98 60 POLY(1) (20,98) 0 1 * * MODELS * .MODEL PIX PNP(BF=100,IS=1E-16) .MODEL NOX NPN(BF=100,VAF=130,IS=1E-14) .MODEL DX D(IS=1E-16) .MODEL SLATCH1 VSWITCH(ROFF=1E6,RON=500,VOFF=2.1,VON=1.4) .ENDS AD8598 -10- REV. A AD8598 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 16-Lead Plastic DIP (N-16) 0.840 (21.33) 0.745 (18.93) 16 1 9 8 0.280 (7.11) 0.240 (6.10) 0.325 (8.25) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93) PIN 1 0.210 (5.33) MAX 0.160 (4.06) 0.115 (2.93) 0.022 (0.558) 0.014 (0.356) 0.100 (2.54) BSC 0.060 (1.52) 0.015 (0.38) 0.130 (3.30) MIN 0.070 (1.77) SEATING 0.045 (1.15) PLANE 0.015 (0.381) 0.008 (0.204) 16-Lead Thin Shrink Small Outline (RU-16) 0.201 (5.10) 0.193 (4.90) 16 9 0.177 (4.50) 0.169 (4.30) 1 8 0.256 (6.50) 0.246 (6.25) 0.006 (0.15) 0.002 (0.05) PIN 1 0.0433 (1.10) MAX 0.0118 (0.30) 0.0075 (0.19) 0.0079 (0.20) 0.0035 (0.090) SEATING PLANE 0.0256 (0.65) BSC 8 0 0.028 (0.70) 0.020 (0.50) 16-Lead Narrow Body IC (R-16A) 0.3937 (10.00) 0.3859 (9.80) 16 1 9 8 0.1574 (4.00) 0.1497 (3.80) 0.2440 (6.20) 0.2284 (5.80) PIN 1 0.0098 (0.25) 0.0040 (0.10) 0.0688 (1.75) 0.0532 (1.35) 0.0196 (0.50) 0.0099 (0.25) 45 SEATING PLANE 0.0500 (1.27) BSC 8 0.0192 (0.49) 0 0.0099 (0.25) 0.0138 (0.35) 0.0075 (0.19) 0.0500 (1.27) 0.0160 (0.41) REV. A -11- PRINTED IN U.S.A. C3452a-8-10/98 |
Price & Availability of AD8598
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |